The microstructure of a melt-spun Zr28Ni44Cu28 (at. %) alloy was characterized in order to determine the structures and compositions of the crystalline phases that compete with glass formation during rapid solidification. Two crystalline phases were identified, namely, a face centered cubic (FCC) zirconium oxide phase and a primitive cubic version of the big-cube oxide phase, using a combination of scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and transmission electron microscopy techniques. Our results indicate that the Zr-O atomic pair interaction is preferential compared to the other atomic pair possibilities, supporting the formation of Zr-based oxides over the equilibrium phases in the ternary Zr-Ni-Cu system. Further, the results provide insight into the mechanisms of oxygen-induced crystallization in Zr-based BMGs and the corresponding decrease in glass forming ability (GFA) with increasing oxygen concentrations.

An alternative route to obtain bulk metallic glasses is by consolidation of metallic glass powders by deforming these materials in the temperature interval between the crystallization temperature and the glass transition temperature, where the material flows with a reduced viscosity. In the present work, bulk parts of the Fe43.2Co28.8B19.2Si4.8Nb4 alloy were produced by hot-pressing gas-atomized powders (GAP) under different uniaxial pressures. Different microstructural analysis revealed that the initial powder as well as the consolidated parts were mostly amorphous, with similar transformation temperatures, showing that bulk samples of this alloy can be produced by conformation in the supercooled liquid region. The sample conformed under the highest pressure (1GPa) exhibited the highest relative density of 96.1±0.5%. These results show that hot pressing of Fe-based gas-atomized powders is a promising route for producing Fe-based bulk metallic glasses.

The Ni57Nb33Zr5Co5 metallic glass is a promising alloy for bipolar plates in proton exchange membrane fuel cells. It is important to know which phase forms in this alloy under different cooling rates in order to understand its influence on the thermal stability and mechanical properties. In this work, melt-spun ribbons and rod samples with 1, 2 and 3 mm diameters were prepared and their phase formation, microstructure and mechanical properties were investigated by X-ray diffraction, differential scanning calorimetry, optical microscopy, scanning electron microscopy and microhardness. It is found that a completely crystalline structure forms in the lower cooling rate samples (2 and 3 mm diameter rods) with the presence of the equilibrium phases Ni3(Nb,Zr) and Nb7Ni6 as primary phases or as a very fine eutectic structure, while a fully glassy structure is attained in the samples with the highest cooling rate (ribbons). For the sample with an intermediate cooling rate (1 mm diameter rod), polymorphically crystals of an unknown metastable phase with spherical morphology precipitate in the glassy matrix with virtually the same composition as the matrix. The 2 mm diameter sample exhibits higher hardness than the other samples, which is attributed to its very fine eutectic colonies.

A good glass former, Ti57.4Cu33.4Ni9.2, was selected using the topological instability criterion (lambda criterion) and the average electronegativity approach. The crystallization behavior and microstructural development of amorphous melt-spun ribbons of this new composition in response to heat treatment were investigated using a combination of differential scanning calorimetry (DSC), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The results indicate that the crystallization of the Ti57.4Cu33.4Ni9.2 alloy takes place through of three exothermic reactions with the nucleation of TiCu, Ti2Cu and Ti2Ni. The kinetics of crystallization were investigated by DSC, and the kinetic parameters were determined using Kissinger’s method.

Earlier works showed that the use of electron beam melting is a viable process to produce NiTi shape memory alloy. In those works a static and a semi-dynamic processes were used producing small shell-shaped and cylindrical ingots respectively. The main characteristics of those samples were low carbon concentration and good composition homogeneity throughout the samples. This paper presents the results of scaling up the ingot size and processing procedure using continuous charge feeding and continuous casting. The composition homogeneity was very good demonstrated by small variation in martensitic transformation temperatures with carbon content around 0.013wt% compared to 0.04 to 0.06wt% of commercial products.